Epoxy High Build MIO Paint

TECHNICAL DATA SHEET

Product Description	This is two pack cold cure High Build Epoxy Finish Paint cured with polyamine hardener . It has excellent corrosion resistance in wide range of corrosive conditions. It also has good resistance to abrasion and impact.
Recommended Uses	This product is used as a heavy duty intermediate or finishing coat for structural steel in Chemical , Fertilizer Plants , Power Plants etc.

PRODUCT SPECIFICATION

Mixing Ratio	Base : Hardener 4 : 1
Colour	All Shades as per customer requirement.
Finish	Semiglossy – Glossy
Pot Life	4 – 5 hrs at 30 °C & 65 % Relative Humidity
Volume Solids	60 % ± 3
Flash point	More than 24 °C
Recommended DFT	80 – 120 microns per coat
Covering Capacity	5 to 8 sq.mtrs / ltr
(Theoretical)
Drying Time	Surface dry – 2 to 3 hrs at 30 °C & 65 % Relative Humidity
	Hard Dry – 10 - 12 hrs max at 30 °C & 65 % Relative Humidity
	Fully cured – 7 days
Recoating Time	Min : 10 - 12 hrs. at 30 °C & 65 % Relative Humidity Max : 7 days
Method of Application	Brush / Airless Spray
Thinner recommended	‘ Epicor ’ Thinner
Shelf life	12 months under normal storage conditions in original sealed containers.

Surface Preparation

Suitably primed surface free from oil , grease , moisture and any other foreign matters.

Remarks 1. Application Data

Method	Pressure ( Atm)	Nozzle	Thinner	Thinner volume
Brush	-	-	Epicor Thinner	0 – 5 %
Airless Spray	4 – 5	0.018 inch to 0.025 inch	Epicor Thinner	0 – 5 %

2. Don’t use below 10 °C
3. Stir well before and while using .
4. Film thickness other than indicated also possible.
5. Mix 15 mins before use .

Safety Precautions :

Provide sufficient ventilation while working with solvent based paints in confined spaces and stagnant air.

Keep the material away from heat , spark and direct flame

Avoid inhalation of solvent vapour or paint mist by using facial mask .Use goggles and gloves to protect against direct contact of paint with
skin and eyes.

In case of contamination , rinse with fresh running water and seek medical help at once.

Follow local & national safety rules.

Special Comments :

Thinner consumption and actual coverage of paint depends on the site conditions.

Stir the paint well before painting and while painting if necessary.

Material should be stored at 30 ºC temperature in dry place.

Epoxy Paint System - EPICOR	:	Epoxy Primer \| Epoxy Finish Paint \| Epoxy High Build Finish Paint-Polyamide Hardener \| Epoxy High Build MIO Paint \| Epoxy Mastic Paint \| One Pack Epoxy Primer \| One Pack Epoxy Finish Paint \| Coal Tar Epoxy Coating Paint \| Special Epoxy Primer for Copper / GI / Aluminium Surface \| Epoxy Zinc Rich Primer
Polyurethane Paint System - POLYCOR	:	Polyurethane Primer \| Polyurethane Finish Paint
Quick Drying Paint System - SPECTRACOAT	:	Quick Drying Primer \| Quick Drying Finish Paint
Synthetic Enamel Paint System - SPECTRACOAT	:	Redoxide Zinc Chromate Primer \| Synthetic Enamel Finish Paint
Heat Resistant Paint System- SPECTRACOAT	:	Heat Resistant Aluminium Paint 200degree C \| Heat Resistant Aluminium Paint 400degree C \| Heat Resistant Aluminium Paint 600degree C
Acrylic Paint System - SPECTRAPLAST	:	Acrylic Primer \| Acrylic Finish Paint \| Acrylic Road Marking Paint
Chlorinated Rubber Paint System- SPECTRACHLOR	:	Chlorinated Rubber Primer \| Chlorinated Rubber Finish Paint
Etch Primer Paint - SPECTRACOAT
Zinc Silicate Coating Paint - SPECTRACOAT

Designed & Hosted by : MID Promoted by : GID