Special Epoxy Primer for Copper / GI / Aluminium Surface

TECHNICAL DATA SHEET

Product Description	This is a high quality two pack modified epoxy polyamide base specially made as anticorrosive and weld able primer.
Recommended Uses	Ideally suitable for copper , G.I., Aluminium & Stainless steel etc surfaces.

PRODUCT SPECIFICATION

Mixing Ratio ( By weight )	Base : Hardener 2 : 1
Colour	Brown and any other iner shades.
Finish	Matt - Eggshell
Pot Life	12 hrs at 30 & C & 65 % Relative Humidity
Volume Solids	40 % + 3
Flash point	More than 20^OC
Recommended DFT	40 + 5 microns per coat
Covering Capacity	12 to 14 sq. mtrs / ltr
( Theoretical )
Drying Time	Surface Dry – 1/2 to 1 hrs at 30^OC & 65 % Relative Humidity
	Hard Dry – 24 hrs at 30^OC & 65 % Relative Humidity
	Fully cured – 7 days
Recoating Time	Minimum - 24 hrs. at 30^OC & 65 % Relative Humidity Max – No limits
Method of Application	Brush / Airless Spray / Conventional spray with precautions.
Thinner recommended	‘ Epicor ’ Special Thinner
Shelf life	12 months under normal storage conditions in original sealed containers.

Surface Preparation	Clean the surface free from oil , grease , moisture and any other foreign matter.
Subsequent Coat	As per recommended coating system.

Remarks 1. Application Data

Method	Pressure ( Atm)	Nozzle	Thinner	Thinner volume
Brush	-	-	Epicor Special Thinner	0 – 5 %
Conventional Spray	3– 4		Epicor Special Thinner	10 – 15 %
Airless Spray	4 – 5	0.021 inch	Epicor Special Thinner	5 – 10 %

2. Don’t use below 10 �C
3. Stir well before and while using .
4. Film thickness other than indicated also possible.
5. Mix 15 mins before use .

Safety Precautions :

Provide sufficient ventilation while working with solvent based paints in confined spaces and stagnant air.

Keep the material away from heat, spark and direct flame

Avoid inhalation of solvent vapour or paint mist by using facial mask .Use goggles and gloves to protect against direct contact of paint with
skin and eyes.

In case of contamination, rinse with fresh running water and seek medical help at once.

Follow local & national safety rules.

Special Comments :

Thinner consumption and actual coverage of paint depends on the site conditions.

Stir the paint well before painting and while painting if necessary.

Material should be stored at 30 �C temperature in dry place.

Epoxy Paint System - EPICOR	:	Epoxy Primer \| Epoxy Finish Paint \| Epoxy High Build Finish Paint-Polyamide Hardener \| Epoxy High Build MIO Paint \| Epoxy Mastic Paint \| One Pack Epoxy Primer \| One Pack Epoxy Finish Paint \| Coal Tar Epoxy Coating Paint \| Special Epoxy Primer for Copper / GI / Aluminium Surface \| Epoxy Zinc Rich Primer
Polyurethane Paint System - POLYCOR	:	Polyurethane Primer \| Polyurethane Finish Paint
Quick Drying Paint System - SPECTRACOAT	:	Quick Drying Primer \| Quick Drying Finish Paint
Synthetic Enamel Paint System - SPECTRACOAT	:	Redoxide Zinc Chromate Primer \| Synthetic Enamel Finish Paint
Heat Resistant Paint System- SPECTRACOAT	:	Heat Resistant Aluminium Paint 200degree C \| Heat Resistant Aluminium Paint 400degree C \| Heat Resistant Aluminium Paint 600degree C
Acrylic Paint System - SPECTRAPLAST	:	Acrylic Primer \| Acrylic Finish Paint \| Acrylic Road Marking Paint
Chlorinated Rubber Paint System- SPECTRACHLOR	:	Chlorinated Rubber Primer \| Chlorinated Rubber Finish Paint
Etch Primer Paint - SPECTRACOAT
Zinc Silicate Coating Paint - SPECTRACOAT

Designed & Hosted by : MID Promoted by : GID