|
Epoxy Primer |
| |
| TECHNICAL DATA SHEET |
| Product Description |
This is two pack
epoxy primer for metal and concrete surfaces . It has good
anticorrosive properties fortified
with
anticorrosive pigments such as red oxide , zinc chrome , zinc
phosphate etc. It is Amine / Amide cured coating . |
| Recommended Uses |
Ideally suitable for use in
varied conditions for the protection of all types of metals . |
|
| |
| PRODUCT SPECIFICATION |
Mixing Ratio
|
Base : Hardener 2 : 1 |
| Colour |
Aluminium, Red Oxide, Grey,
Yellow or any other inert shades. |
| Finish |
Eggshell – Semiglossy |
| Pot Life |
6 hrs at 30°C & 65
% Relative Humidity |
| Volume Solids |
40 % ± 3 |
| Flash point |
More than 24 °C |
| Recommended DFT |
30 ± 5 microns per
coat |
| Covering Capacity |
12 to 14 sq.mtrs /
ltr |
| (Theoretical) |
|
| Drying Time |
Surface dry – 1/2
to 1 hrs at 30°C & 65 % Relative Humidity |
|
Hard Dry – 8 - 10 hrs max at
30°C & 65 % Relative Humidity |
|
Fully cured – 7 days |
| Recoating Time |
6 – 8 hrs. at 30°C & 65 %
Relative Humidi |
| Method of Application |
Brush / Conventional Spray /
Airless Spray |
| Thinner recommended |
‘ Epicor ’ Thinner |
| Shelf life |
12 months under normal storage
conditions in original sealed containers. |
|
| |
Surface Preparation
|
New Steel : Recommended for
abrasive blasting to Sa 2 ½ after degreasing and deoiling of the
surface. If steel
is coated by Shop Primer , clean damages to
shop primer and clean the surface free from oil , grease ,
moisture
and any other foreign matter.
Maintenance : Remove oil , grease
etc with a detergent wash . Remove salts and other contaminants
by
high pressure fresh water hosing. Allow
surface to dry before the application. |
| Subsequent coat |
As per recommended coating
system. |
|
| |
| Remarks 1. Application
Data |
| Method |
Pressure ( Atm) |
Nozzle |
Thinner |
Thinner volume |
| Brush |
- |
- |
Epicor Thinner |
0 – 5 % |
| Conventional Spray |
3– 4 |
|
Epicor Thinner |
5 – 10 % |
| Airless Spray |
4 – 5 |
0.018 inch to 0.025 inch |
Epicor Thinner |
0 – 5 % |
|
| |
2. Don’t use below 10° C
3. Stir well before and while using .
4. Film thickness other than indicated also possible.
5. Mix 15 mins before use . |
| |
| Safety Precautions : |
 Provide
sufficient ventilation while working with solvent based paints in
confined spaces and stagnant air.
Keep the
material away from heat , spark and direct flame
Avoid
inhalation of solvent vapour or paint mist by using facial mask. Use
goggles and gloves to protect against direct contact of paint with skin
and eyes.
In case of
contamination, rinse with fresh running water and seek medical help at
once.
Follow local
& national safety rules. |
| |
| Special Comments : |
Thinner
consumption and actual coverage of paint depends on the site conditions.
Stir the
paint well before painting and while painting if necessary.
Material
should be stored at 30ºC temperature in dry place. |
| |
| |
 |
| |
|
| |
